The PhdCodedEnumerationObservation reports PHD measurements that contain a Enum-Observed-Value-Simple-OID attribute.

This type of measurement is used when the Personal Health Device reports a measurement as an IEEE 11073-10101 code. An example would be the most recent meal context associated with a glucose measurement such as 'breakfast', 'fasting', 'snack', etc. The list of codes for these meal options is finite.

Provides a reason why the expected value in the element Observation.valueCodeableConcept is missing.

Only the Measurement-Status/status flags indicating invalid, not unavailable, or msmt ongoing will generate this element and cause the value[x] to be absent. The remaining settings of the status values are reported in the meta.security element or interpretation element.

The PhdCodedEnumerationObservation reports PHD measurements that contain a Enum-Observed-Value-Simple-OID attribute.

This type of measurement is used when the Personal Health Device reports a measurement as an IEEE 11073-10101 code. An example would be the most recent meal context associated with a glucose measurement such as 'breakfast', 'fasting', 'snack', etc. The list of codes for these meal options is finite.

The metadata about the resource. This is content that is maintained by the infrastructure. Changes to the content might not always be associated with version changes to the resource.

Security labels applied to this resource. These tags connect specific resources to the overall security policy and infrastructure.

The security labels can be updated without changing the stated version of the resource. The list of security labels is a set. Uniqueness is based the system/code, and version and display are ignored.

Security Labels from the Healthcare Privacy and Security Classification System.

Security labels applied to this resource. These tags connect specific resources to the overall security policy and infrastructure.

The security labels can be updated without changing the stated version of the resource. The list of security labels is a set. Uniqueness is based the system/code, and version and display are ignored.

Security Labels from the Healthcare Privacy and Security Classification System.

The identification of the code system that defines the meaning of the symbol in the code.

The URI may be an OID (urn:oid:...) or a UUID (urn:uuid:...). OIDs and UUIDs SHALL be references to the HL7 OID registry. Otherwise, the URI should come from HL7's list of FHIR defined special URIs or it should reference to some definition that establishes the system clearly and unambiguously.

Need to be unambiguous about the source of the definition of the symbol.

A symbol in syntax defined by the system. The symbol may be a predefined code or an expression in a syntax defined by the coding system (e.g. post-coordination).

Need to refer to a particular code in the system.

A reference to a set of rules that were followed when the resource was constructed, and which must be understood when processing the content. Often, this is a reference to an implementation guide that defines the special rules along with other profiles etc.

Asserting this rule set restricts the content to be only understood by a limited set of trading partners. This inherently limits the usefulness of the data in the long term. However, the existing health eco-system is highly fractured, and not yet ready to define, collect, and exchange data in a generally computable sense. Wherever possible, implementers and/or specification writers should avoid using this element. Often, when used, the URL is a reference to an implementation guide that defines these special rules as part of it's narrative along with other profiles, value sets, etc.

An Extension

An Extension

Source of the definition for the extension code - a logical name or a URL.

The definition may point directly to a computable or human-readable definition of the extensibility codes, or it may be a logical URI as declared in some other specification. The definition SHALL be a URI for the Structure Definition defining the extension.

Value of extension - must be one of a constrained set of the data types (see Extensibility for a list).

May be used to represent additional information that is not part of the basic definition of the resource and that modifies the understanding of the element that contains it and/or the understanding of the containing element's descendants. Usually modifier elements provide negation or qualification. To make the use of extensions safe and manageable, there is a strict set of governance applied to the definition and use of extensions. Though any implementer is allowed to define an extension, there is a set of requirements that SHALL be met as part of the definition of the extension. Applications processing a resource are required to check for modifier extensions.

Modifier extensions SHALL NOT change the meaning of any elements on Resource or DomainResource (including cannot change the meaning of modifierExtension itself).

There can be no stigma associated with the use of extensions by any application, project, or standard - regardless of the institution or jurisdiction that uses or defines the extensions. The use of extensions is what allows the FHIR specification to retain a core level of simplicity for everyone.

Modifier extensions allow for extensions that cannot be safely ignored to be clearly distinguished from the vast majority of extensions which can be safely ignored. This promotes interoperability by eliminating the need for implementers to prohibit the presence of extensions. For further information, see the definition of modifier extensions.

A unique identifier assigned to this observation.

Allows observations to be distinguished and referenced.

An identifier created from a combination of the measurement parameters like sensor time stamp, type code, value, units code, patient and device identifiers, and selected elements of any component elements.

This value is used in the conditional create to prevent data duplication. PHDs will often re-send already sent data for a variety of reasons. This element is required unless the metric measurement contains no time stamp or is a measurement containing a time stamp that is real time. By real time the time stamp reported by the PHD must be later than the current time reported by the PHD before any measurements are received. There might be other means to ascertain whether the data is real time. Temporarily stored data from IEEE 11073-20601 devices, which are required to delete the data after sending, can also be considered real time. Temporarily stored data from Bluetooth Low Energy Health devices may be resent so these cannot be considered as real time.

Allows observations to be distinguished in a selective enough manner to prevent resource duplication.

The purpose of this identifier.

Applications can assume that an identifier is permanent unless it explicitly says that it is temporary.

Identifies the purpose for this identifier, if known .

Allows the appropriate identifier for a particular context of use to be selected from among a set of identifiers.

A coded type for the identifier that can be used to determine which identifier to use for a specific purpose.

This element deals only with general categories of identifiers. It SHOULD not be used for codes that correspond 1..1 with the Identifier.system. Some identifiers may fall into multiple categories due to common usage. Where the system is known, a type is unnecessary because the type is always part of the system definition. However systems often need to handle identifiers where the system is not known. There is not a 1:1 relationship between type and system, since many different systems have the same type.

A coded type for an identifier that can be used to determine which identifier to use for a specific purpose.

Allows users to make use of identifiers when the identifier system is not known.

Establishes the namespace for the value - that is, a URL that describes a set values that are unique.

Identifier.system is always case sensitive.

There are many sets of identifiers. To perform matching of two identifiers, we need to know what set we're dealing with. The system identifies a particular set of unique identifiers.

The portion of the identifier typically relevant to the user and which is unique within the context of the system.

If the value is a full URI, then the system SHALL be urn:ietf:rfc:3986. The value's primary purpose is computational mapping. As a result, it may be normalized for comparison purposes (e.g. removing non-significant whitespace, dashes, etc.) A value formatted for human display can be conveyed using the Rendered Value extension. Identifier.value is to be treated as case sensitive unless knowledge of the Identifier.system allows the processer to be confident that non-case-sensitive processing is safe.

The status of the result value. Either 'final' or 'preliminary'

The value shall be set to 'final' unless a Measurement-Status attribute or Nu-Observed-Value attribute status field indicates that the measurement is preliminary. In that case this field shall be set to 'preliminary'

Codes providing the status of an observation.

Need to track the status of individual results. Some results are finalized before the whole report is finalized.

A code that classifies the general type of observation being made.

In addition to the required category valueset, this element allows various categorization schemes based on the owner’s definition of the category and effectively multiple categories can be used at once. The level of granularity is defined by the category concepts in the value set.

Codes for high level observation categories.

Used for filtering what observations are retrieved and displayed.

A code that classifies the general type of observation being made.

The category enables identifying observations generated by PHDs.

Codes for high level observation categories.

Used for filtering what observations are retrieved and displayed.

A reference to a code defined by a terminology system.

Codes may be defined very casually in enumerations, or code lists, up to very formal definitions such as SNOMED CT - see the HL7 v3 Core Principles for more information. Ordering of codings is undefined and SHALL NOT be used to infer meaning. Generally, at most only one of the coding values will be labeled as UserSelected = true.

Allows for alternative encodings within a code system, and translations to other code systems.

The identification of the code system that defines the meaning of the symbol in the code.

The URI may be an OID (urn:oid:...) or a UUID (urn:uuid:...). OIDs and UUIDs SHALL be references to the HL7 OID registry. Otherwise, the URI should come from HL7's list of FHIR defined special URIs or it should reference to some definition that establishes the system clearly and unambiguously.

Need to be unambiguous about the source of the definition of the symbol.

A symbol in syntax defined by the system. The symbol may be a predefined code or an expression in a syntax defined by the coding system (e.g. post-coordination).

Need to refer to a particular code in the system.

Describes what was observed. Sometimes this is called the observation "name".

All code-value and, if present, component.code-component.value pairs need to be taken into account to correctly understand the meaning of the observation.

Codes identifying names of simple observations.

Knowing what kind of observation is being made is essential to understanding the observation.

A reference to a code defined by a terminology system.

Codes may be defined very casually in enumerations, or code lists, up to very formal definitions such as SNOMED CT - see the HL7 v3 Core Principles for more information. Ordering of codings is undefined and SHALL NOT be used to infer meaning. Generally, at most only one of the coding values will be labeled as UserSelected = true.

Allows for alternative encodings within a code system, and translations to other code systems.

This MDC code expresses what the measurement is

For non-compound 11073-20601 metric numeric measurements, this code is obtained from one or more of the Type, Metric-Id, Nu-Observed-Value, and Metric-Id-Partition attributes. The algorithm to get the 16-bit partition and 16-bit term code is as follows: 1. The partition and term code are obtained from the Type attribute. 2. If there is a Metric-Id attribute the term code comes from this attribute. 3. If there is a Nu-Observed-Value attribute the term code comes from this attribute. 4. If the term code is NOT from the Type attribute, and there is a Metric-Id-Partition attribute, the partition comes from this attribute. 5. The 32-bit 11073-10101 code value is given by partition * 2 **16 + term code. It is this value that is placed in the code.coding.code element for this MDCType slice. For compound numeric measurements, the code comes from the Type attribute.

Allows for alternative encodings within a code system, and translations to other code systems.

The identification of the code system that defines the meaning of the symbol in the code.

The URI may be an OID (urn:oid:...) or a UUID (urn:uuid:...). OIDs and UUIDs SHALL be references to the HL7 OID registry. Otherwise, the URI should come from HL7's list of FHIR defined special URIs or it should reference to some definition that establishes the system clearly and unambiguously.

Need to be unambiguous about the source of the definition of the symbol.

A symbol in syntax defined by the system. The symbol may be a predefined code or an expression in a syntax defined by the coding system (e.g. post-coordination).

Required for all measurements

Need to refer to a particular code in the system.

This LOINC code expresses what the measurement is

If the measurement is one of the magic vital signs, the Magic LOINC code for that vital sign as specified by FHIR appears here.

Allows for alternative encodings within a code system, and translations to other code systems.

The identification of the code system that defines the meaning of the symbol in the code.

The URI may be an OID (urn:oid:...) or a UUID (urn:uuid:...). OIDs and UUIDs SHALL be references to the HL7 OID registry. Otherwise, the URI should come from HL7's list of FHIR defined special URIs or it should reference to some definition that establishes the system clearly and unambiguously.

Need to be unambiguous about the source of the definition of the symbol.

A symbol in syntax defined by the system. The symbol may be a predefined code or an expression in a syntax defined by the coding system (e.g. post-coordination).

Required if the measurement is a vital sign

Need to refer to a particular code in the system.

The patient, or group of patients, location, or device this observation is about and into whose record the observation is placed. If the actual focus of the observation is different from the subject (or a sample of, part, or region of the subject), the focus element or the code itself specifies the actual focus of the observation.

One would expect this element to be a cardinality of 1..1. The only circumstance in which the subject can be missing is when the observation is made by a device that does not know the patient. In this case, the observation SHALL be matched to a patient through some context/channel matching technique, and at this point, the observation should be updated.

Observations have no value if you don't know who or what they're about.

A reference to a location at which the other resource is found. The reference may be a relative reference, in which case it is relative to the service base URL, or an absolute URL that resolves to the location where the resource is found. The reference may be version specific or not. If the reference is not to a FHIR RESTful server, then it should be assumed to be version specific. Internal fragment references (start with '#') refer to contained resources.

Using absolute URLs provides a stable scalable approach suitable for a cloud/web context, while using relative/logical references provides a flexible approach suitable for use when trading across closed eco-system boundaries. Absolute URLs do not need to point to a FHIR RESTful server, though this is the preferred approach. If the URL conforms to the structure "/[type]/[id]" then it should be assumed that the reference is to a FHIR RESTful server.

The time or time-period the observed value is asserted as being true. It is a time period if a Measure-Active-Period (duration) attribute is part of the metric measurement sent by the PHD. Otherwise it is the time stamp sent by the PHD or the time of reception by the PHG if the PHD sent no time stamp.

At least a date should be present unless this observation is a historical report. For recording imprecise or "fuzzy" times (For example, a blood glucose measurement taken "after breakfast") use the Timing datatype which allow the measurement to be tied to regular life events.

Knowing when an observation was deemed true is important to its relevance as well as determining trends.

The information determined as a result of making the observation, if the information has a simple value.

An observation may have; 1) a single value here, 2) both a value and a set of related or component values, or 3) only a set of related or component values. If a value is present, the datatype for this element should be determined by Observation.code. A CodeableConcept with just a text would be used instead of a string if the field was usually coded, or if the type associated with the Observation.code defines a coded value. For additional guidance, see the Notes section below.

An observation exists to have a value, though it might not if it is in error, or if it represents a group of observations.

A reference to a code defined by a terminology system.

Codes may be defined very casually in enumerations, or code lists, up to very formal definitions such as SNOMED CT - see the HL7 v3 Core Principles for more information. Ordering of codings is undefined and SHALL NOT be used to infer meaning. Generally, at most only one of the coding values will be labeled as UserSelected = true.

Allows for alternative encodings within a code system, and translations to other code systems.

A reference to a code defined by a terminology system.

Codes may be defined very casually in enumerations, or code lists, up to very formal definitions such as SNOMED CT - see the HL7 v3 Core Principles for more information. Ordering of codings is undefined and SHALL NOT be used to infer meaning. Generally, at most only one of the coding values will be labeled as UserSelected = true.

Allows for alternative encodings within a code system, and translations to other code systems.

The identification of the code system that defines the meaning of the symbol in the code.

The URI may be an OID (urn:oid:...) or a UUID (urn:uuid:...). OIDs and UUIDs SHALL be references to the HL7 OID registry. Otherwise, the URI should come from HL7's list of FHIR defined special URIs or it should reference to some definition that establishes the system clearly and unambiguously.

Need to be unambiguous about the source of the definition of the symbol.

Provides a reason why the expected value in the element Observation.valueCodeableConcept is missing.

Only the Measurement-Status/status flags indicating invalid, not unavailable, or msmt ongoing will generate this element and cause the value[x] to be absent. The remaining settings of the status values are reported in the meta.security element or interpretation element.

Codes specifying why the result (Observation.value[x]) is missing.

For many results it is necessary to handle exceptional values in measurements.

A reference to a code defined by a terminology system.

Codes may be defined very casually in enumerations, or code lists, up to very formal definitions such as SNOMED CT - see the HL7 v3 Core Principles for more information. Ordering of codings is undefined and SHALL NOT be used to infer meaning. Generally, at most only one of the coding values will be labeled as UserSelected = true.

Allows for alternative encodings within a code system, and translations to other code systems.

A reference to a code defined by a terminology system.

Codes may be defined very casually in enumerations, or code lists, up to very formal definitions such as SNOMED CT - see the HL7 v3 Core Principles for more information. Ordering of codings is undefined and SHALL NOT be used to infer meaning. Generally, at most only one of the coding values will be labeled as UserSelected = true.

Allows for alternative encodings within a code system, and translations to other code systems.

The identification of the code system that defines the meaning of the symbol in the code.

The URI may be an OID (urn:oid:...) or a UUID (urn:uuid:...). OIDs and UUIDs SHALL be references to the HL7 OID registry. Otherwise, the URI should come from HL7's list of FHIR defined special URIs or it should reference to some definition that establishes the system clearly and unambiguously.

Need to be unambiguous about the source of the definition of the symbol.

A symbol in syntax defined by the system. The symbol may be a predefined code or an expression in a syntax defined by the coding system (e.g. post-coordination).

Need to refer to a particular code in the system.

The device used to generate the observation data.

This field will reference the PHD Device.

Reference to the device-related resources that describe the sensor device taking the measurement. This element will point to a Device resource following the Phd Device Profile.

This reference points to the Device resource containing information about the sensor device that took the measurement.

Some observations have multiple component observations. These component observations are expressed as separate code value pairs that share the same attributes. Examples include systolic and diastolic component observations for blood pressure measurement and multiple component observations for genetics observations.

For a discussion on the ways Observations can be assembled in groups together see Notes below.

Component observations share the same attributes in the Observation resource as the primary observation and are always treated a part of a single observation (they are not separable). However, the reference range for the primary observation value is not inherited by the component values and is required when appropriate for each component observation.

May be used to represent additional information that is not part of the basic definition of the element and that modifies the understanding of the element in which it is contained and/or the understanding of the containing element's descendants. Usually modifier elements provide negation or qualification. To make the use of extensions safe and manageable, there is a strict set of governance applied to the definition and use of extensions. Though any implementer can define an extension, there is a set of requirements that SHALL be met as part of the definition of the extension. Applications processing a resource are required to check for modifier extensions.

Modifier extensions SHALL NOT change the meaning of any elements on Resource or DomainResource (including cannot change the meaning of modifierExtension itself).

There can be no stigma associated with the use of extensions by any application, project, or standard - regardless of the institution or jurisdiction that uses or defines the extensions. The use of extensions is what allows the FHIR specification to retain a core level of simplicity for everyone.

Modifier extensions allow for extensions that cannot be safely ignored to be clearly distinguished from the vast majority of extensions which can be safely ignored. This promotes interoperability by eliminating the need for implementers to prohibit the presence of extensions. For further information, see the definition of modifier extensions.

Describes what was observed. Sometimes this is called the observation "code".

All code-value and component.code-component.value pairs need to be taken into account to correctly understand the meaning of the observation.

Codes identifying names of simple observations.

Knowing what kind of observation is being made is essential to understanding the observation.

For each partition:term code pair contained in the Supplemental-Types attribute, a separate supplementalTypesComponent element is generated. The component is not generated if the attribute is absent or empty. The component shall be generated otherwise.

A PHD may send a Supplemental-Types attribute as part of the measurement. This attribute consists of a set of MDC nomenclature codes as partition:term code pairs. Each pair is a code describing something additional about the measurement, such as MDC_MODALITY_SPOT in the pulse oximeter which indicates that the provided measurement is a stable average. An MDC_MODALITY_FAST would indicate that a short averaging is used and the result reported regardless of stability.

Component observations share the same attributes in the Observation resource as the primary observation and are always treated a part of a single observation (they are not separable). However, the reference range for the primary observation value is not inherited by the component values and is required when appropriate for each component observation.

May be used to represent additional information that is not part of the basic definition of the element and that modifies the understanding of the element in which it is contained and/or the understanding of the containing element's descendants. Usually modifier elements provide negation or qualification. To make the use of extensions safe and manageable, there is a strict set of governance applied to the definition and use of extensions. Though any implementer can define an extension, there is a set of requirements that SHALL be met as part of the definition of the extension. Applications processing a resource are required to check for modifier extensions.

Modifier extensions SHALL NOT change the meaning of any elements on Resource or DomainResource (including cannot change the meaning of modifierExtension itself).

There can be no stigma associated with the use of extensions by any application, project, or standard - regardless of the institution or jurisdiction that uses or defines the extensions. The use of extensions is what allows the FHIR specification to retain a core level of simplicity for everyone.

Modifier extensions allow for extensions that cannot be safely ignored to be clearly distinguished from the vast majority of extensions which can be safely ignored. This promotes interoperability by eliminating the need for implementers to prohibit the presence of extensions. For further information, see the definition of modifier extensions.

Describes what was observed. Sometimes this is called the observation "code".

All code-value and component.code-component.value pairs need to be taken into account to correctly understand the meaning of the observation.

Knowing what kind of observation is being made is essential to understanding the observation.

A reference to a code defined by a terminology system.

Codes may be defined very casually in enumerations, or code lists, up to very formal definitions such as SNOMED CT - see the HL7 v3 Core Principles for more information. Ordering of codings is undefined and SHALL NOT be used to infer meaning. Generally, at most only one of the coding values will be labeled as UserSelected = true.

Allows for alternative encodings within a code system, and translations to other code systems.

A reference to a code defined by a terminology system.

Codes may be defined very casually in enumerations, or code lists, up to very formal definitions such as SNOMED CT - see the HL7 v3 Core Principles for more information. Ordering of codings is undefined and SHALL NOT be used to infer meaning. Generally, at most only one of the coding values will be labeled as UserSelected = true.

Allows for alternative encodings within a code system, and translations to other code systems.

The identification of the code system that defines the meaning of the symbol in the code.

The URI may be an OID (urn:oid:...) or a UUID (urn:uuid:...). OIDs and UUIDs SHALL be references to the HL7 OID registry. Otherwise, the URI should come from HL7's list of FHIR defined special URIs or it should reference to some definition that establishes the system clearly and unambiguously.

Need to be unambiguous about the source of the definition of the symbol.

68193 is the 32-bit nomenclature code indicating a 'Supplemental-Types' value

Need to refer to a particular code in the system.

The information determined as a result of making the observation, if the information has a simple value.

Used when observation has a set of component observations. An observation may have both a value (e.g. an Apgar score) and component observations (the observations from which the Apgar score was derived). If a value is present, the datatype for this element should be determined by Observation.code. A CodeableConcept with just a text would be used instead of a string if the field was usually coded, or if the type associated with the Observation.code defines a coded value. For additional guidance, see the Notes section below.

An observation exists to have a value, though it might not if it is in error, or if it represents a group of observations.

The supplemental information determined as a result of making the observation, if the information is a code.

Used when observation has a set of component observations. An observation may have both a value (e.g. an Apgar score) and component observations (the observations from which the Apgar score was derived). If a value is present, the datatype for this element should be determined by Observation.code. A CodeableConcept with just a text would be used instead of a string if the field was usually coded, or if the type associated with the Observation.code defines a coded value. For additional guidance, see the Notes section below.

An observation exists to have a value, though it might not if it is in error, or if it represents a group of observations.

A reference to a code defined by a terminology system.

Codes may be defined very casually in enumerations, or code lists, up to very formal definitions such as SNOMED CT - see the HL7 v3 Core Principles for more information. Ordering of codings is undefined and SHALL NOT be used to infer meaning. Generally, at most only one of the coding values will be labeled as UserSelected = true.

Allows for alternative encodings within a code system, and translations to other code systems.

A reference to a code defined by a terminology system.

Codes may be defined very casually in enumerations, or code lists, up to very formal definitions such as SNOMED CT - see the HL7 v3 Core Principles for more information. Ordering of codings is undefined and SHALL NOT be used to infer meaning. Generally, at most only one of the coding values will be labeled as UserSelected = true.

Allows for alternative encodings within a code system, and translations to other code systems.

The identification of the code system that defines the meaning of the symbol in the code.

The URI may be an OID (urn:oid:...) or a UUID (urn:uuid:...). OIDs and UUIDs SHALL be references to the HL7 OID registry. Otherwise, the URI should come from HL7's list of FHIR defined special URIs or it should reference to some definition that establishes the system clearly and unambiguously.

Need to be unambiguous about the source of the definition of the symbol.

For the given Supplemental-Types entry the code here is given by: partition * 2**16 + term code

Need to refer to a particular code in the system.

Provides a reason why the expected value in the element Observation.component.value[x] is missing.

"Null" or exceptional values can be represented two ways in FHIR Observations. One way is to simply include them in the value set and represent the exceptions in the value. For example, measurement values for a serology test could be "detected", "not detected", "inconclusive", or "test not done".

The alternate way is to use the value element for actual observations and use the explicit dataAbsentReason element to record exceptional values. For example, the dataAbsentReason code "error" could be used when the measurement was not completed. Because of these options, use-case agreements are required to interpret general observations for exceptional values.

Codes specifying why the result (Observation.value[x]) is missing.

For many results it is necessary to handle exceptional values in measurements.

This component shall be present if the measurement contains a Relative-Time-Stamp.

Relative time stamps are converted to wall clock time by the PHG through the Coincident Time Stamp Observation. The original relative time value shall be provided here in order to recover the data sent by the sensor device. It also provided a higher time resolution than permitted by the effective[x] time stamp should it be needed. The Relative-Time-Stamp is a 32-bit unsigned integer in units of 1/8th ms. It is reported here scaled to microseconds.

Component observations share the same attributes in the Observation resource as the primary observation and are always treated a part of a single observation (they are not separable). However, the reference range for the primary observation value is not inherited by the component values and is required when appropriate for each component observation.

May be used to represent additional information that is not part of the basic definition of the element and that modifies the understanding of the element in which it is contained and/or the understanding of the containing element's descendants. Usually modifier elements provide negation or qualification. To make the use of extensions safe and manageable, there is a strict set of governance applied to the definition and use of extensions. Though any implementer can define an extension, there is a set of requirements that SHALL be met as part of the definition of the extension. Applications processing a resource are required to check for modifier extensions.

Modifier extensions SHALL NOT change the meaning of any elements on Resource or DomainResource (including cannot change the meaning of modifierExtension itself).

There can be no stigma associated with the use of extensions by any application, project, or standard - regardless of the institution or jurisdiction that uses or defines the extensions. The use of extensions is what allows the FHIR specification to retain a core level of simplicity for everyone.

Modifier extensions allow for extensions that cannot be safely ignored to be clearly distinguished from the vast majority of extensions which can be safely ignored. This promotes interoperability by eliminating the need for implementers to prohibit the presence of extensions. For further information, see the definition of modifier extensions.

Describes what was observed. Sometimes this is called the observation "code".

All code-value and component.code-component.value pairs need to be taken into account to correctly understand the meaning of the observation.

Knowing what kind of observation is being made is essential to understanding the observation.

A reference to a code defined by a terminology system.

Codes may be defined very casually in enumerations, or code lists, up to very formal definitions such as SNOMED CT - see the HL7 v3 Core Principles for more information. Ordering of codings is undefined and SHALL NOT be used to infer meaning. Generally, at most only one of the coding values will be labeled as UserSelected = true.

Allows for alternative encodings within a code system, and translations to other code systems.

A reference to a code defined by a terminology system.

Codes may be defined very casually in enumerations, or code lists, up to very formal definitions such as SNOMED CT - see the HL7 v3 Core Principles for more information. Ordering of codings is undefined and SHALL NOT be used to infer meaning. Generally, at most only one of the coding values will be labeled as UserSelected = true.

Allows for alternative encodings within a code system, and translations to other code systems.

The identification of the code system that defines the meaning of the symbol in the code.

The URI may be an OID (urn:oid:...) or a UUID (urn:uuid:...). OIDs and UUIDs SHALL be references to the HL7 OID registry. Otherwise, the URI should come from HL7's list of FHIR defined special URIs or it should reference to some definition that establishes the system clearly and unambiguously.

Need to be unambiguous about the source of the definition of the symbol.

The MDC code of the Relative-Time-Stamp attribute

Need to refer to a particular code in the system.

The information determined as a result of making the observation, if the information has a simple value.

Used when observation has a set of component observations. An observation may have both a value (e.g. an Apgar score) and component observations (the observations from which the Apgar score was derived). If a value is present, the datatype for this element should be determined by Observation.code. A CodeableConcept with just a text would be used instead of a string if the field was usually coded, or if the type associated with the Observation.code defines a coded value. For additional guidance, see the Notes section below.

An observation exists to have a value, though it might not if it is in error, or if it represents a group of observations.

The information determined as a result of making the observation, if the information has a simple value.

Used when observation has a set of component observations. An observation may have both a value (e.g. an Apgar score) and component observations (the observations from which the Apgar score was derived). If a value is present, the datatype for this element should be determined by Observation.code. A CodeableConcept with just a text would be used instead of a string if the field was usually coded, or if the type associated with the Observation.code defines a coded value. For additional guidance, see the Notes section below.

An observation exists to have a value, though it might not if it is in error, or if it represents a group of observations.

The value of the relative time attribute which is in units of 1/8th milliseconds scaled to microseconds.

The implicit precision in the value should always be honored. Monetary values have their own rules for handling precision (refer to standard accounting text books).

Precision is handled implicitly in almost all cases of measurement.

How the value should be understood and represented - whether the actual value is greater or less than the stated value due to measurement issues; e.g. if the comparator is "<" , then the real value is < stated value.

How the Quantity should be understood and represented.

Need a framework for handling measures where the value is <5ug/L or >400mg/L due to the limitations of measuring methodology.

The unit code shall use the UCUM system

Need to know the system that defines the coded form of the unit.

The UCUM code for microseconds

The preferred system is UCUM, but SNOMED CT can also be used (for customary units) or ISO 4217 for currency. The context of use may additionally require a code from a particular system.

Need a computable form of the unit that is fixed across all forms. UCUM provides this for quantities, but SNOMED CT provides many units of interest.

Provides a reason why the expected value in the element Observation.component.value[x] is missing.

"Null" or exceptional values can be represented two ways in FHIR Observations. One way is to simply include them in the value set and represent the exceptions in the value. For example, measurement values for a serology test could be "detected", "not detected", "inconclusive", or "test not done".

The alternate way is to use the value element for actual observations and use the explicit dataAbsentReason element to record exceptional values. For example, the dataAbsentReason code "error" could be used when the measurement was not completed. Because of these options, use-case agreements are required to interpret general observations for exceptional values.

Codes specifying why the result (Observation.value[x]) is missing.

For many results it is necessary to handle exceptional values in measurements.

This component shall be present if the measurement contains Hi-Res-Relative-Time-Stamp.

Hi Res Relative time stamps are converted to wall clock time by the PHG through the Coincident Time Stamp Observation. The original relative time value shall be provided here in order to recover the data sent by the sensor device. It also allows much higher time resolution than permitted in the effective{x] element should it be needed. The Hi-Res-Relative-Time-Stamp is a 64-bit unsigned interger in units of microseconds.

Component observations share the same attributes in the Observation resource as the primary observation and are always treated a part of a single observation (they are not separable). However, the reference range for the primary observation value is not inherited by the component values and is required when appropriate for each component observation.

May be used to represent additional information that is not part of the basic definition of the element and that modifies the understanding of the element in which it is contained and/or the understanding of the containing element's descendants. Usually modifier elements provide negation or qualification. To make the use of extensions safe and manageable, there is a strict set of governance applied to the definition and use of extensions. Though any implementer can define an extension, there is a set of requirements that SHALL be met as part of the definition of the extension. Applications processing a resource are required to check for modifier extensions.

Modifier extensions SHALL NOT change the meaning of any elements on Resource or DomainResource (including cannot change the meaning of modifierExtension itself).

There can be no stigma associated with the use of extensions by any application, project, or standard - regardless of the institution or jurisdiction that uses or defines the extensions. The use of extensions is what allows the FHIR specification to retain a core level of simplicity for everyone.

Modifier extensions allow for extensions that cannot be safely ignored to be clearly distinguished from the vast majority of extensions which can be safely ignored. This promotes interoperability by eliminating the need for implementers to prohibit the presence of extensions. For further information, see the definition of modifier extensions.

Describes what was observed. Sometimes this is called the observation "code".

All code-value and component.code-component.value pairs need to be taken into account to correctly understand the meaning of the observation.

Knowing what kind of observation is being made is essential to understanding the observation.

A reference to a code defined by a terminology system.

Codes may be defined very casually in enumerations, or code lists, up to very formal definitions such as SNOMED CT - see the HL7 v3 Core Principles for more information. Ordering of codings is undefined and SHALL NOT be used to infer meaning. Generally, at most only one of the coding values will be labeled as UserSelected = true.

Allows for alternative encodings within a code system, and translations to other code systems.

A reference to a code defined by a terminology system.

Codes may be defined very casually in enumerations, or code lists, up to very formal definitions such as SNOMED CT - see the HL7 v3 Core Principles for more information. Ordering of codings is undefined and SHALL NOT be used to infer meaning. Generally, at most only one of the coding values will be labeled as UserSelected = true.

Allows for alternative encodings within a code system, and translations to other code systems.

The identification of the code system that defines the meaning of the symbol in the code.

The URI may be an OID (urn:oid:...) or a UUID (urn:uuid:...). OIDs and UUIDs SHALL be references to the HL7 OID registry. Otherwise, the URI should come from HL7's list of FHIR defined special URIs or it should reference to some definition that establishes the system clearly and unambiguously.

Need to be unambiguous about the source of the definition of the symbol.

The MDC code for the Hi-Res-Relative-Time-Stamp attribute

Need to refer to a particular code in the system.

The information determined as a result of making the observation, if the information has a simple value.

Used when observation has a set of component observations. An observation may have both a value (e.g. an Apgar score) and component observations (the observations from which the Apgar score was derived). If a value is present, the datatype for this element should be determined by Observation.code. A CodeableConcept with just a text would be used instead of a string if the field was usually coded, or if the type associated with the Observation.code defines a coded value. For additional guidance, see the Notes section below.

An observation exists to have a value, though it might not if it is in error, or if it represents a group of observations.

The information determined as a result of making the observation, if the information has a simple value.

Used when observation has a set of component observations. An observation may have both a value (e.g. an Apgar score) and component observations (the observations from which the Apgar score was derived). If a value is present, the datatype for this element should be determined by Observation.code. A CodeableConcept with just a text would be used instead of a string if the field was usually coded, or if the type associated with the Observation.code defines a coded value. For additional guidance, see the Notes section below.

An observation exists to have a value, though it might not if it is in error, or if it represents a group of observations.

The value of the hi res relative time attribute (already in microseconds).

The implicit precision in the value should always be honored. Monetary values have their own rules for handling precision (refer to standard accounting text books).

Precision is handled implicitly in almost all cases of measurement.

How the value should be understood and represented - whether the actual value is greater or less than the stated value due to measurement issues; e.g. if the comparator is "<" , then the real value is < stated value.

How the Quantity should be understood and represented.

Need a framework for handling measures where the value is <5ug/L or >400mg/L due to the limitations of measuring methodology.

The unit code shall use the UCUM system

Need to know the system that defines the coded form of the unit.

The UCUM code for microseconds

The preferred system is UCUM, but SNOMED CT can also be used (for customary units) or ISO 4217 for currency. The context of use may additionally require a code from a particular system.

Need a computable form of the unit that is fixed across all forms. UCUM provides this for quantities, but SNOMED CT provides many units of interest.

Provides a reason why the expected value in the element Observation.component.value[x] is missing.

"Null" or exceptional values can be represented two ways in FHIR Observations. One way is to simply include them in the value set and represent the exceptions in the value. For example, measurement values for a serology test could be "detected", "not detected", "inconclusive", or "test not done".

The alternate way is to use the value element for actual observations and use the explicit dataAbsentReason element to record exceptional values. For example, the dataAbsentReason code "error" could be used when the measurement was not completed. Because of these options, use-case agreements are required to interpret general observations for exceptional values.

Codes specifying why the result (Observation.value[x]) is missing.

For many results it is necessary to handle exceptional values in measurements.

The PhdCodedEnumerationObservation reports PHD measurements that contain a Enum-Observed-Value-Simple-OID attribute.

This type of measurement is used when the Personal Health Device reports a measurement as an IEEE 11073-10101 code. An example would be the most recent meal context associated with a glucose measurement such as 'breakfast', 'fasting', 'snack', etc. The list of codes for these meal options is finite.

The logical id of the resource, as used in the URL for the resource. Once assigned, this value never changes.

The only time that a resource does not have an id is when it is being submitted to the server using a create operation.

The metadata about the resource. This is content that is maintained by the infrastructure. Changes to the content might not always be associated with version changes to the resource.

Unique id for the element within a resource (for internal references). This may be any string value that does not contain spaces.

May be used to represent additional information that is not part of the basic definition of the element. To make the use of extensions safe and manageable, there is a strict set of governance applied to the definition and use of extensions. Though any implementer can define an extension, there is a set of requirements that SHALL be met as part of the definition of the extension.

There can be no stigma associated with the use of extensions by any application, project, or standard - regardless of the institution or jurisdiction that uses or defines the extensions. The use of extensions is what allows the FHIR specification to retain a core level of simplicity for everyone.

The version specific identifier, as it appears in the version portion of the URL. This value changes when the resource is created, updated, or deleted.

The server assigns this value, and ignores what the client specifies, except in the case that the server is imposing version integrity on updates/deletes.

When the resource last changed - e.g. when the version changed.

This value is always populated except when the resource is first being created. The server / resource manager sets this value; what a client provides is irrelevant. This is equivalent to the HTTP Last-Modified and SHOULD have the same value on a read interaction.

A uri that identifies the source system of the resource. This provides a minimal amount of Provenance information that can be used to track or differentiate the source of information in the resource. The source may identify another FHIR server, document, message, database, etc.

In the provenance resource, this corresponds to Provenance.entity.what[x]. The exact use of the source (and the implied Provenance.entity.role) is left to implementer discretion. Only one nominated source is allowed; for additional provenance details, a full Provenance resource should be used.

This element can be used to indicate where the current master source of a resource that has a canonical URL if the resource is no longer hosted at the canonical URL.

A list of profiles (references to StructureDefinition resources) that this resource claims to conform to. The URL is a reference to StructureDefinition.url.

It is up to the server and/or other infrastructure of policy to determine whether/how these claims are verified and/or updated over time. The list of profile URLs is a set.

Security labels applied to this resource. These tags connect specific resources to the overall security policy and infrastructure.

The security labels can be updated without changing the stated version of the resource. The list of security labels is a set. Uniqueness is based the system/code, and version and display are ignored.

Security Labels from the Healthcare Privacy and Security Classification System.

Security labels applied to this resource. These tags connect specific resources to the overall security policy and infrastructure.

The security labels can be updated without changing the stated version of the resource. The list of security labels is a set. Uniqueness is based the system/code, and version and display are ignored.

Security Labels from the Healthcare Privacy and Security Classification System.

Unique id for the element within a resource (for internal references). This may be any string value that does not contain spaces.

May be used to represent additional information that is not part of the basic definition of the element. To make the use of extensions safe and manageable, there is a strict set of governance applied to the definition and use of extensions. Though any implementer can define an extension, there is a set of requirements that SHALL be met as part of the definition of the extension.

There can be no stigma associated with the use of extensions by any application, project, or standard - regardless of the institution or jurisdiction that uses or defines the extensions. The use of extensions is what allows the FHIR specification to retain a core level of simplicity for everyone.

The identification of the code system that defines the meaning of the symbol in the code.

The URI may be an OID (urn:oid:...) or a UUID (urn:uuid:...). OIDs and UUIDs SHALL be references to the HL7 OID registry. Otherwise, the URI should come from HL7's list of FHIR defined special URIs or it should reference to some definition that establishes the system clearly and unambiguously.

Need to be unambiguous about the source of the definition of the symbol.

The version of the code system which was used when choosing this code. Note that a well-maintained code system does not need the version reported, because the meaning of codes is consistent across versions. However this cannot consistently be assured, and when the meaning is not guaranteed to be consistent, the version SHOULD be exchanged.

Where the terminology does not clearly define what string should be used to identify code system versions, the recommendation is to use the date (expressed in FHIR date format) on which that version was officially published as the version date.

A symbol in syntax defined by the system. The symbol may be a predefined code or an expression in a syntax defined by the coding system (e.g. post-coordination).

Need to refer to a particular code in the system.

A representation of the meaning of the code in the system, following the rules of the system.

Need to be able to carry a human-readable meaning of the code for readers that do not know the system.

Indicates that this coding was chosen by a user directly - e.g. off a pick list of available items (codes or displays).

Amongst a set of alternatives, a directly chosen code is the most appropriate starting point for new translations. There is some ambiguity about what exactly 'directly chosen' implies, and trading partner agreement may be needed to clarify the use of this element and its consequences more completely.

This has been identified as a clinical safety criterium - that this exact system/code pair was chosen explicitly, rather than inferred by the system based on some rules or language processing.

Tags applied to this resource. Tags are intended to be used to identify and relate resources to process and workflow, and applications are not required to consider the tags when interpreting the meaning of a resource.

The tags can be updated without changing the stated version of the resource. The list of tags is a set. Uniqueness is based the system/code, and version and display are ignored.

Codes that represent various types of tags, commonly workflow-related; e.g. "Needs review by Dr. Jones".

A reference to a set of rules that were followed when the resource was constructed, and which must be understood when processing the content. Often, this is a reference to an implementation guide that defines the special rules along with other profiles etc.

Asserting this rule set restricts the content to be only understood by a limited set of trading partners. This inherently limits the usefulness of the data in the long term. However, the existing health eco-system is highly fractured, and not yet ready to define, collect, and exchange data in a generally computable sense. Wherever possible, implementers and/or specification writers should avoid using this element. Often, when used, the URL is a reference to an implementation guide that defines these special rules as part of it's narrative along with other profiles, value sets, etc.

The base language in which the resource is written.

Language is provided to support indexing and accessibility (typically, services such as text to speech use the language tag). The html language tag in the narrative applies to the narrative. The language tag on the resource may be used to specify the language of other presentations generated from the data in the resource. Not all the content has to be in the base language. The Resource.language should not be assumed to apply to the narrative automatically. If a language is specified, it should it also be specified on the div element in the html (see rules in HTML5 for information about the relationship between xml:lang and the html lang attribute).

A human language.

A human-readable narrative that contains a summary of the resource and can be used to represent the content of the resource to a human. The narrative need not encode all the structured data, but is required to contain sufficient detail to make it "clinically safe" for a human to just read the narrative. Resource definitions may define what content should be represented in the narrative to ensure clinical safety.

Contained resources do not have narrative. Resources that are not contained SHOULD have a narrative. In some cases, a resource may only have text with little or no additional discrete data (as long as all minOccurs=1 elements are satisfied). This may be necessary for data from legacy systems where information is captured as a "text blob" or where text is additionally entered raw or narrated and encoded information is added later.

These resources do not have an independent existence apart from the resource that contains them - they cannot be identified independently, and nor can they have their own independent transaction scope.

This should never be done when the content can be identified properly, as once identification is lost, it is extremely difficult (and context dependent) to restore it again. Contained resources may have profiles and tags In their meta elements, but SHALL NOT have security labels.

An Extension

Unique id for the element within a resource (for internal references). This may be any string value that does not contain spaces.

An Extension

Source of the definition for the extension code - a logical name or a URL.

The definition may point directly to a computable or human-readable definition of the extensibility codes, or it may be a logical URI as declared in some other specification. The definition SHALL be a URI for the Structure Definition defining the extension.

Value of extension - must be one of a constrained set of the data types (see Extensibility for a list).

May be used to represent additional information that is not part of the basic definition of the resource and that modifies the understanding of the element that contains it and/or the understanding of the containing element's descendants. Usually modifier elements provide negation or qualification. To make the use of extensions safe and manageable, there is a strict set of governance applied to the definition and use of extensions. Though any implementer is allowed to define an extension, there is a set of requirements that SHALL be met as part of the definition of the extension. Applications processing a resource are required to check for modifier extensions.

Modifier extensions SHALL NOT change the meaning of any elements on Resource or DomainResource (including cannot change the meaning of modifierExtension itself).

There can be no stigma associated with the use of extensions by any application, project, or standard - regardless of the institution or jurisdiction that uses or defines the extensions. The use of extensions is what allows the FHIR specification to retain a core level of simplicity for everyone.

Modifier extensions allow for extensions that cannot be safely ignored to be clearly distinguished from the vast majority of extensions which can be safely ignored. This promotes interoperability by eliminating the need for implementers to prohibit the presence of extensions. For further information, see the definition of modifier extensions.

A unique identifier assigned to this observation.

Allows observations to be distinguished and referenced.

An identifier created from a combination of the measurement parameters like sensor time stamp, type code, value, units code, patient and device identifiers, and selected elements of any component elements.

This value is used in the conditional create to prevent data duplication. PHDs will often re-send already sent data for a variety of reasons. This element is required unless the metric measurement contains no time stamp or is a measurement containing a time stamp that is real time. By real time the time stamp reported by the PHD must be later than the current time reported by the PHD before any measurements are received. There might be other means to ascertain whether the data is real time. Temporarily stored data from IEEE 11073-20601 devices, which are required to delete the data after sending, can also be considered real time. Temporarily stored data from Bluetooth Low Energy Health devices may be resent so these cannot be considered as real time.

Allows observations to be distinguished in a selective enough manner to prevent resource duplication.

Unique id for the element within a resource (for internal references). This may be any string value that does not contain spaces.

May be used to represent additional information that is not part of the basic definition of the element. To make the use of extensions safe and manageable, there is a strict set of governance applied to the definition and use of extensions. Though any implementer can define an extension, there is a set of requirements that SHALL be met as part of the definition of the extension.

There can be no stigma associated with the use of extensions by any application, project, or standard - regardless of the institution or jurisdiction that uses or defines the extensions. The use of extensions is what allows the FHIR specification to retain a core level of simplicity for everyone.

The purpose of this identifier.

Applications can assume that an identifier is permanent unless it explicitly says that it is temporary.

Identifies the purpose for this identifier, if known .

Allows the appropriate identifier for a particular context of use to be selected from among a set of identifiers.

A coded type for the identifier that can be used to determine which identifier to use for a specific purpose.

This element deals only with general categories of identifiers. It SHOULD not be used for codes that correspond 1..1 with the Identifier.system. Some identifiers may fall into multiple categories due to common usage. Where the system is known, a type is unnecessary because the type is always part of the system definition. However systems often need to handle identifiers where the system is not known. There is not a 1:1 relationship between type and system, since many different systems have the same type.

A coded type for an identifier that can be used to determine which identifier to use for a specific purpose.

Allows users to make use of identifiers when the identifier system is not known.

Establishes the namespace for the value - that is, a URL that describes a set values that are unique.

Identifier.system is always case sensitive.

There are many sets of identifiers. To perform matching of two identifiers, we need to know what set we're dealing with. The system identifies a particular set of unique identifiers.

The portion of the identifier typically relevant to the user and which is unique within the context of the system.

If the value is a full URI, then the system SHALL be urn:ietf:rfc:3986. The value's primary purpose is computational mapping. As a result, it may be normalized for comparison purposes (e.g. removing non-significant whitespace, dashes, etc.) A value formatted for human display can be conveyed using the Rendered Value extension. Identifier.value is to be treated as case sensitive unless knowledge of the Identifier.system allows the processer to be confident that non-case-sensitive processing is safe.