Release 5 Ballot

This page is part of the FHIR Specification (v5.0.0-ballot: FHIR R5 Ballot Preview). The current version which supercedes this version is 5.0.0. For a full list of available versions, see the Directory of published versions . Page versions: R5 R4B R4 R3

4.3.2.159 CodeSystem urn:oid:1.2.36.1.2001.1001.101.104.16592

FHIR Infrastructure Work Group Maturity Level: 0Informative Use Context: Any

This is a code system defined by the FHIR project.

Summary

Defining URL:urn:oid:1.2.36.1.2001.1001.101.104.16592
Version:5.0.0-ballot
Name:PatientMedicineChangeTypes
Title:Patient Medicine Change Types
Status:draft
Definition:

Example Item Flags for the List Resource. In this case, these are the kind of flags that would be used on a medication list at the end of a consultation.

Committee:FHIR Infrastructure Work Group
OID:2.16.840.1.113883.4.642.4.321 (for OID based terminology systems)
Copyright:

Copyright © 2012-2013 National E-Health Transition Authority Ltd : This document contains information which is protected by copyright. All Rights Reserved. No part of this work may be reproduced or used in any form or by any means--graphic, electronic, or mechanical, including photocopying, recording, taping, or information storage and retrieval systems--without the permission of NEHTA. All copies of this document must include the copyright and other information contained on this page. Revision 1 Telephone: 1300 901 001 or email: servicedesk@nehta.gov.au Disclaimer: The National E-Health Transition Authority Ltd (NEHTA) makes the information and other material ('Information') in this document available in good faith but without any representation or warranty as to its accuracy or completeness. NEHTA cannot accept any responsibility for the consequences of any use of the Information. As the Information is of a general nature only, it is up to any person using or relying on the Information to ensure that it is accurate, complete and suitable for the circumstances of its use.

Flags:CaseSensitive, Complete
All codes ValueSet:Patient Medicine Change Types

This Code system is used in the following value sets:

  • ValueSet: Patient Medicine Change Types (Example Item Flags for the List Resource. In this case, these are the kind of flags that would be used on a medication list at the end of a consultation.)

4.3.2.159.1 Content

This code system urn:oid:1.2.36.1.2001.1001.101.104.16592 defines the following codes:

CodeDisplayDefinitionCopy
01 UnchangedNo change has been made to the status of this medicine item. 
02 ChangedThe medicine item has changed. The change may be described in an extension (not defined yet) 
03 CancelledThe prescription for this medicine item was cancelled by an authorized health care provider. The patient may be advised to complete the course of the prescribed medicine. This advice is a clinical decision made based on assessment of the patient's clinical condition. 
04 PrescribedA new medicine item has been prescribed 
05 CeasedAdministration of this medication item that the patient is currently taking is stopped or recommended to be stopped (i.e. instructed to be ceased by a health care provider). This cessation is anticipated to be permanent. The Change Description should describe the reason for cessation. Example uses: the medication in question is considered ineffective or has caused serious adverse effects. This value applies both to the cessation of a medication that is prescribed by another healthcare provider or patient self-administration of OTC medicines. 
06 SuspendedAdministration of this medication item that the patient is currently taking is on hold, or instructed or recommended by a health care provider to be temporarily stopped, or subject to clinical review (i.e. the stop may be temporary or permanent depending on the outcome of clinical review), or temporarily suspended as a pre-requisite to certain surgical or diagnostic procedures. 

 

See the full registry of code systems defined as part of FHIR.

Explanation of the columns that may appear on this page:

LevelA few code lists that FHIR defines are hierarchical - each code is assigned a level. See Code System for further information.
SourceThe source of the definition of the code (when the value set draws in codes defined elsewhere)
CodeThe code (used as the code in the resource instance). If the code is in italics, this indicates that the code is not selectable ('Abstract')
DisplayThe display (used in the display element of a Coding). If there is no display, implementers should not simply display the code, but map the concept into their application
DefinitionAn explanation of the meaning of the concept
CommentsAdditional notes about how to use the code